Allen Bradley Modules 1788-CNET 1788 CNET AB 1788CNET Interface Card

Allen Bradley Modules 1788-CNET 1788 CNET AB 1788CNET Interface Card

Product Description:

For the requested packet interval, enter the number of milliseconds desired between each I/O message
between the ControlLogix processor and the 1203-CN1. The 1203-CN1 can handle a packet interval as
low as 5 milliseconds; therefore, make sure that this value is set to at least Click the "Finish" button to
complete the configuration of the I/O connection in RSLogix 5000. At this point, download your configuration to the ControlLogix processor, then exit RSLogix 5000. To actually schedule the I/O, you will need to start RSNetWorx for ControlNet. Once RSNetWorx starts, go online to the ControlNet network
containing the ControlLogix chassis and 1203-CN1 being configured. Turn on the "Enable Edits" check box, then save the network. This causes the I/O connection created in RSLogix 5000 to be scheduled in the ControlLogix processor. After a few seconds, the I/O LED on the ControlLogix processor and the module LED on the 1203-CN1 should stop blinking and remain green. If they do not, it could indicate a number of I/O-related problems

Related Product Recommendation:

Product's Character:

The Remote I/O communications module allows a SCANport product to look and act like a Remote I/O chassis when connected to a programmable controller. Data contained in the input/output image table is transferred between the programmable controller by the Remote I/O scanner, the same as with any Remote I/O chassis. You control the location of data transferred by setting the rack address and
starting group. You control the amount of data by setting the DIP switches on SW3. Important: Thecommunications module does not scale the data that is transferred. Consequently, all scaling of the data must be done in the controller. Refer to the user manual for your SCANport product for details on
device units. Important: The Remote I/O to SCANport conversion is asynchronous. Data sent to the adapter for transfer to the drive must be maintained until the drive has received data.DIP switches on SW3 determine how the data contained in the programmable controller I/O image table is used in the drive. Figure shows an I/O image table.

1772-LS PLC-2/05 PLC-2/05 Processor AB
1772-LW PLC 2/17 MINI PLC 2/17 Processor AB
1772-LWP D PLC2 DNGL SL 6K Proc AB
1772-LX/C PLC 2/16 Mini PLC 2/16 Processor AB
1772-LX/D PLC 2/16 Mini PLC 2/16 Processor AB
1772-LXP Mini PLC 2/16 Processor AB
1774-MA 4 K Memory Module AB
1774-SD Remote I/O Module AB
1774-SR Remote I/O Half Scanner Module AB
1774-TB2 Interface Module AB
1775-A3 PLC-3/10 PLC-3 Chassis AB
1775-KA Communication Adapter AB
1775-L4 Main Processor Module AB
1775-MS4 Error Correcting Memory 16K Ram AB
1775-P2 Power Supply AB
1775-P3 Multi-Output Power Supply AB
1775-SR5 I/O Scanner Communications Module AB
1777-CP Terminator AB
1784-CP13 2801–N8 Video Interface Cable AB
1784-KT/B ISA/EISA Communication Module AB
1784-KTX ISA Communication Module AB
1784-PCICS PCI Bus Messaging Module AB
1784-PKTX/A PCI Network Interface Card - Series A AB
1784-PKTX/B PCI Network Interface Card - Series B AB
1785-ENET/A 96204473 Ethernet Interface Module AB
1785-KA Communication Adapter Module AB
1785-KA3 DH PLC-2 INTFC Communication Adapter Module AB
1785-L11B /11 /11 Processor Module AB
1785-L20B/C /20 /20 Processor Module - Series C AB
1785-L20B/E /20 /20 Processor Module AB

Opal ETD Board 50312575100 Circuit Board AMAT SemVision cX working

Opal DVD Board 50312540200 Circuit Board AMAT SemVision cX working

Lambda PA-3N-4-6SG-001 AC DC Power Supply AMAT SemVision cX working

AMAT 50309050000 SEM Electron Column SV300 LT AMAT SemVision cX used working

Opal SRA3 Board 30612530100 Circuit Board AMAT SemVision cX working

Varian Diode Ion Pump Large AMAT SemVision cX used working

VAT 0200X-BA24-AIE2 Pneumatic Slit Valve AMAT SemVision cX used working

Opal MIS2 Board 30612550000 Circuit Board AMAT SemVision cX working

Opal HDF Board 50312510000 Circuit Board 0006300T WD64AA-75AA AMAT SemVision cX

Oram Power Supply LPS850 AMAT SemVision cX working

RH Electronics 50419700100 OM Power Supply Cage OMP AMAT SemVision cX used works

A to Z Electronics 50312640000 ASA Board Assy AMAT SemVision cX used working

AMAT RadiSys WHC DR 300 0650-A0750 Computer 2A01640AA4A AMAT SemVision cX workin

HiTek G303/51 High Voltage Power Supply & Cable AMAT 50414710200 used working

AMAT SemVision cX CVC Board 50312570000 working

A to Z Electronics 50312403000 HV Module Assy CDM3-i AMAT SemVision cX working

Parker Veriflow 45700342 Point of Use Regulator SQ140E503PLFSFFM used working

ZTE B9100 ZXMBW BaseBand Unit Type B used working

CMC BMR2005TCD00CEA001 PM Servo Motor w/ RHS-20-50-CC-SP Actuator used working

The use of the product:

Moore Automationare still working and able to shipping worldwide

Our company has many products in stock,which are immediately available.The warranty is 1 years which apply to all the new products.If you purchase one more parts from us,we can make a discount to you.
If you have any question pls do not hesitate to contact us.We can supply all kind of the automaiton parts,if you want to purchase parts pls send the parts model to my mail, I will prompt reply you asa I receive the
Hope anyone enquire from us.

it is a leading global supplier of control system components. We specialize in control systems and drives.
With many years of experience in the industrial sector, we consistently deliver the highest quality of spare parts.

We have tens of thousands of spare parts and spare parts warehouse . Products and services to serve for installing of users control system,
Distributed control systems, programmable controllers, panel controller and drive!

* Our mission is to help you!
* Reduced maintenance costs!

We have a large inventory of control system components. We also made a lot of new hardware and discontinued spare parts to help supporting your existing control systems.

We have experienced staff, extensive testing , all the spare parts which we sold are with warranty period of one year, and they have undergone rigorous testing and certification!