Integrity promise Connaught, intentions to do everything.
Passed Certifications - ISO9001:2015
TN Product tested by National Coal Science Institute and Provincial
Quality Inspection Center
Especially the sealing lip which is made of special fibre, is
suitable to be used in the state of running with high speed. This
sealing lip could lower the friction and calorific value of the
deep groove ball bearing. Deep groove ball bearing has simple
structure, and it is easier to reach to a higher manufacture
precision compared with other bearings, so it is suitable for
volume-production. Together with low cost of production, deep
groove ball bearing is widely used in the conveyor idler bearing
Basic type; With snap ring groove on the outer ring (-N); With one
shield (-Z) on one side or two shields (-2Z) on both sides; With
one seal (-RS) on one side or two seals (-2RS) on both sides.
All of Our products are made of Chrome Steel GCr15, with grinding
groove and superfinishing technology.
Mining machine, conveyor machine, Engineering Machinery, Agricultural Machinery,
Construction Machinery, textile, chemical, auto motor,
Transportation Vehicles, General industrial Equipment, etc.
Catalog of Deep groove ball bearing
XKTE bearing's most fundamental difference is:
The other manufacturers make products considering the price cheap,
but we make products considering the service life. Each of the
idler roller bearings we produce is fully implemented in the
national standard. XKTE bearings exist for their quality and brand.
You can deny our price, but you can never find out our products'
defects in quality. XKTE conveying machinery bearing, a big brand,
is worthy of your trust.
First, the identification of the bearing
Formal manufacturers use laser engraving. The stamps are deep, have
significant dents with hand touch, good-looking, with no
breakpoints, and are never disappeared. This obviously improves the
The use of bearing retainer
Bearing retainer selection is very important. Because once too much
dust stuck into the bearing, the retainer will be first worn. If
the bearing retainer is broken, the bearing will be directly
broken. Imported bearings use big rivets to thicken retainers. XKTE
bearing is completely in accordance with the process of imported
production, so each piece of ours is made to a high quality, and
guaranteed to operate for thirty thousand hours.
Selection of nylon retainer
Nylon retainer bearing is often used in the mine. Nylon retainer
has better anti-stuck performance and wider range of temperature
than iron retainer. In the underground its anti-static performance
is also better. To get safety certificate for coal mining products
must use nylon retainer KA bearing. The selection of nylon retainer
is crucial to KA idler roller bearing, while the material of nylon
retainer must be pure and has enough toughness and strength,
because the retainer will get very soft if it is made of bad
material or mixed material, thus to make no anti-stuck performance
within the bearing.
The ring is the main part and the important part of the idler
roller bearing. Best idler roller bearing has deep groove ball, and
large clearance. But deep groove doesn't mean to dig the channel
with a simple way of enlarge the steel ball. The thickness of the bearing is certain, so to get the ball big
and the groove deep will shorten service life. Our XKTE bearing
uses way of thickening ring to get the standard of deep groove and
large clearance, improves the anti-stuck performance, and
effectively increases the service life.
Bearing material and hardness
Good idler roller bearing must be made of bearing steel, named
"High Carbon Chromium Bearing Steel (Fully quenched class) GCr15".
At present the standard hardness of idler roller bearing is 60-65
degree, while hardness of ring is 61-62 degree, andball is 64-65
The simple way to identify idler roller bearing is to see if its
hardness is over 60 degree, because only bearing steel can get over
Grease selection of roller bearing
Many customers ignore this most critical point. The
thirty-thousands-hours operation is a very long term. This has to
be guaranteed by enough quality and quantity grease. And this
should also be taken into account of working in different seasons.
Special note: please choose special high temperature grease if
working environment is over 120 °C for long time or low temperature
grease if it below -20 °C.
The key points of idler roller accessories installation
Must remember the key points of idler roller accessories
installation. The idler roller accessories are effective in order
to play its own value. Idler roller accessories SKF bearing during
cooling in the width direction has also contracted, so the
installation should apply some pressure to the inner shoulder
pressing, and after cooling with thin feeler test for detection,
whether there is a gap between the inner ring end face and bearing
shoulder. Found to achieve the required heating temperature, it
should be installed as soon as possible, so as to avoid cooling and
installation difficulties. The heating temperature should be
controlled, high temperature of SKF bearing damage, the temperature
is too low then ring expansion is insufficient, the effect is not
significant. The thermal expansion of the inner diameter of the
inner diameter of the inner ring, which is obtained from the
temperature in the small control, 1000 to 80 degrees Celsius, is
sufficient for the SKF bearing with a general surplus amount.
The impact to the idler roller caused by external environment on
accessories is great, according to the actual choice of the
appropriate idler roller accessories; according to the production
of idler roller to choose the appropriate idler roller accessories.
Such as nylon idler roller, the application of what kind of
accessories, as well as rubber idler roller should choose what kind
of accessories; production process is the choice of accessories
should be noted in a large area.
1. Industrial packaging : Single box + outer carton + pallets
2. Neutral Packing:
Tube package + outer carton + pallets
Tube package + middle box + outer carton + pallets
3. As buyer's request
1) TT, 30% deposit , 70% before shippment.
2) L/C at sight. (high bank charge, not suggest , but acceptable )
3) 100% Western Union in advance. (specially for air shipment or
For small orders,we send by express UPS,DHL,FEDEX, or EMS
with Thracking number. For big quantity, we will ship by air or by
|Delivery date||Normally stock within 3-7 days. Bulk quantity within 30 days.|
|Payment terms||T/T L/C|
| ||2. For small amount, we accept Western Union|
|Samples Policy :|
Small sample free and bulk sample cost needed and freight
We will reduct this part expense from the total value when place
Started 2006, We are a manufacture of industrial Bearing in
Liaocheng Shandong, concentrates on manufacturing industrial
bearing, mainly used in conveying equipment, machinery, textile,
chemical, auto motor and so on. Especially bearing for conveyor,
which make us become one of well-known enterprise in China. We have
26 production lines, mainly produce deep groove ball bearing,
spherical roller bearing, TN Nylon cage bearing and sealed bearing.
All of Our products are made of Chrome Steel GCr15, with grinding
groove and superfinishing technology. Supply ability is about 20000
Pieces / per Day. We have our own brand XKTE, and we can also
provide OEM service.
I couldn't find a design to fit my application in your catalog. Can
you help me design a bearing?
Yes, technical expertise is available to assist you with
engineering design for custom products. Available options include,
but are not limited to, custom rings, retainers, balls, shields,
lubricants, and packaging. We look forward to working with you to
satisfy your rotary motion requirements.
What causes bearing noise?
Bearing noise is a function of both the bearing and the way it is
used. Some external factors that affect bearing noise include
lubricant type, excessive bearing load, and improper installation.
Once the abnormal noise occurred, you can contact our engineers, we
will help you find the reasons and provide the appropriate
What is the difference between using a shield or a seal as a ball
Shields or seals are often installed to retain lubricant and to
prevent contamination from entering the bearing. While a shield
contacts the outer ring and does not come in contact with the inner
ring, the seal generally comes in contact with both the inner and
outer rings. Torque or drag is lower with a shield than with a
seal. Alternately, the seal provides a higher degree of protection
from contamination. Shields and seals are available in a variety of
materials and configurations.
XKTE developed a serious of sealing methods for different
applications. Please contact a XKTE engineer for technical
assistance with any special requirements.
Why choose us ?
1. professional commitment to conveying machinery bearing, leading
enterprise of conveyor
machinery bearing in China.
2. With background of about 10 years
3. Strict Inspection ,and the best quality price with reasonable
price bearings provided .
4. OEM service provided.
5. Delivery products from our factory warehouse , short delivery
Email:firstname.lastname@example.org Skype ID: xktekevin
Address: Xu Village Industrial Garden, Gan Town, Guan County,