Green Fine Copper Wire Making Machine High Reliability 1800m/Min Max Line Speed

HXE-20DT Fine copper wire drawing machine with annealer

I. Quick details

HXE-20DT Fine copper wire drawing machine with annealer is used to draw and anneal single bare copper wire from 0.8mm-1.6mm to 0.15mm-0.55mm.

II. Main Technical parameters

1. Usage single bare copper wire drawing and annealing
2. Inlet size 0.8mm-1.6mm
3. Outlet size 0.15mm-0.55mm (Elongation of annealed wire 25% to 32%)
4. Machine speed/max 1800m/min
5. Die number 20, Dies size 25mm×8-10mmT, Slip ratio 15%+8%
6. Wire drawing mode standing-mode and 4axes
7. Drive by Inverter control, Brand Inovance, Most widely used brand in drawing machine
8. Main motor 15KW, Spooler motor 3.7KW, China best brand
9. Annealing voltage DC50V/max, Annealing current DC450A/max, Annealing power 22KVA
10. Annealing method DC Three section annealing
11. Annealing protection will be done by steam protection
12. Capacity of compressed air 0.4-0.6Mpa, 20L/min
13. Demand Water quantity for annealing and coolant 200L/min
14. Machine frame welded by steel plate
15. Transmission Flat belts
16. Capstan Ceramic plasma
17. Lubricating system Pipe Spray
18. Bobbin size 300mm, loading capacity: 50kg/max
19. Bobbin loading & unloading type shaft type
20. Traversing unit 110W synchros motor, width: 270mm/max
21. Tension control by Air pressure tension control (With Weight balance as Backup)
22. Cabinet 0.8m*0.6m*2.0m
23. Machine dimension 2.3m*1.6m*1.9m; Installation Area 3.3m*1.7m+0.8*0.6m
24. Machine weight 3400KG, Cabinet weight 500KG. In total for shipping around 4,000KG.

III. Components

IV. The structure and principle of the machine

4-1. The annealing part, is three-section annealing, consist of Preheating section, annealing section and drying section. The fix speed capstan of drawing, the annealing capstans, are driven by the same motor, through belts, so the speed of drawing, speed of annealing, is the same, make sure no wire break.

4-2. The annealing capstans, are access to positive and negative power, make the wire pass through the annealing capstans with current, by short-circuiting, to preheat, anneal and dry.

4-3. The annealing current and voltage, by auto tracking the drawing speed to auto adjust.

4-4. To cooling fast to achieve the annealing, the annealing capstan is under the cooling water. There is a cooling tank at the bottom of the machine, cooling water, better use fat content of 0.5% emulsion. The pump shall pump the cooling water through the pipe and the switch to the annealing door. Adjust the cooling water switch to make sure the water is in certain height.

4-5. To make sure the wire while annealing, no Oxidation, there is a steam-in protection pipe, connect the pipe to the Steam generator, to use the steam to protect the wire from the oxidation.

4-6. In the exit of the drying section, there is a blowing device. In the device, shall have two dies. Connect the air compressor to the air compress input pipe, then out by the blowing device, adjust the switch, to make all the left water of the drying part, on the surface of the wire, blow away.

V. Advantage and after-sale service

A: Advantage

(1). HENGXIE has some world famous parts suppliers, has special lubrication system for the gears and bearing.
(2). Body and other key components and parts are produced by our own factory , quality is reliable.
(3). DC. three-section annealing
(4). Our company’s developing process in more than 10 years.

B: After-self service

Our company for all machine product, since the shipment date, our company free after sale maintenance service guarantee period is:
(1) 1 year for mechanical part.
(2) 6 month for electrical part.

Under these situation mentioned, the Seller will not take responsibility, but if the Buyer agree, will charge fees accordingly to repair the machine.
1. Due to wrong operation while shipping.
2. Due to Buyer`s wrong preparation that may cause damage to the machine.
3. Due to Buyer`s wrong operation that may cause damage to the machine.
4. Not in the consuming part list.
5. After agreement are made for the shipping, for any damage, Buyer should inform Seller in letter form to repair in seven days, If beyond the dare, Seller shall take no responsibility.
6. For any other failures due to acts of God (such as lightning, typhoon, earthquake, riots, war, fire or flood) and other factors that will cause damage, Seller shall take no responsibility.
7. Seller guarantee provide long term support regarding the parts and teach. After warranty, will charge accordingly.

Suzhou Hengxie Machinery Co., Ltd was established in 2005, a total professional in drawing machine field, specialized in copper and aluminium wire drawing machines. Located in Suzhou City, very close to Shanghai, we share a convenient transportation and the most successful working environment.

Our 6,700 square meters of land allows producing a wide range of equipment, developing and researching new products. We always strive to introduce the latest international techniques to update our products.

With management concept of “Excellent quality, Reasonable prices, Superior services”, our hope is to not only meet our customers` expectations but to exceed them.

Here are the machines we have: Copper&Aluminium Rod Breakdown machine, Large and intermediate wire drawing machine with online annealer, Intermediate wire drawing machine, Intermediate wire drawing machine with online annealer, Fine wire drawing machine, Fine wire drawing machine with online annealer, Customized fine wire drawing machine with annealer, Super fine wire drawing machine. As long as we talk, we can always meet your detail requirements.

Our market includes both domestic and overseas. Such as Bangladesh, Egypt, Iran, Malaysia, Syria, Algeria, Kenya, Turkey, South Africa, Latin America and so on.

With the concept of “Stable quality and mutual development”, Hengxie welcome all customers from the world to create a sincere cooperation and win-win benefit in the future.