Product Details
Free calibration of level transmitter with GPS tracker in tank
Product Description
1. Products Introduction
KCF series Capacitive digital oil level sensor is
made of stainless steel. It applies the principle of the liquid
flotage and magnetic induction to measure the liquid level. The
product has good anti-corrosion performance, high measuring
precision and preventing oil leakage when turned over. These made
the sensor be widely used in light truck, bus, boat, and
engineering mechanism fields. Graceful design and excellentquality
attract the world famous vehicle OEM.The KCF series sensor is a cost effective fuel level sensor
designed for smaller trucks. The sensor is designed according to
the actual tank shape for exact measurements of the tank content.
Measurements are done by series of reed switches positioned inside
the level tube. A float. with built- in magnets then triggers the
reed relays. generating a potential - free resistance with a ohm
value that increases or decreases according to the respective fluid
level. Resistance output is fully customizable. The float is the
only moving part of the sensor. thereby minimize potential
mechanical failures. All sensors are fully insulated to protect
against voltage inside the tank.
2. Parameters
Material | 304 stainless steel |
Pressure Range | -0.1MPa~0.4MPa |
Length range | 100~1400mm |
Installation | thread mounting M20×1.5 or flange mounting, special specifications
can be costomized |
Probe diameter | φ16 |
Working current | <10ma |
Power Supply | DC5V, 9~36V |
Wire | PVC material (PA corrugated pipe aacover is optional) |
Explosion-proof grade | Explosion-proof ExdIIC T5 |
Output signal | 4~20mA, 4~20mA superimposed HART communication, 485 communication,
CAN bus communication |
Accuracy | 0.01 |
Operating Temperature | -40℃~+85 ℃ |
Protection Grade | IP67 |
3. Installation method
The wiring method is as follows:
RS232: The sensor output in this way has 4 wires
Red 24V+
Black 24V-(RS232)
Blue RS232 (RXD) computer sender
Yellow RS232 (TXD) computer receiver
4 to 20 mA: The sensor output in this mode has 2 wires
Red 24V+
Black 24V-
0 to 5V: The sensor output in this mode has 3 wires.
Red 24V+
Black 24V-
Blue 0~5V voltage output
note:
There can only be one type of RS232/ 0-5V/4~20mA signal, and one of
them can be used arbitrarily.
The sensor uses microcomputer technology and can be directly used
for measurement of various weakly corrosive liquids without
calibration.
Installation of the sensor:
1 If it is an old car, the original sensor needs to be removed. The
new car is installed directly;
2 Please check the accessories before installation: flange, rubber
pad, O-ring, whether the screws are complete and consistent;
3 Place the O-ring on the root of the sensor;
4 Apply oil-resistant sealant to both sides of the rubber pad, and
then fix the hole position with the flange and the fuel tank
flange, and fix it with screws. When tightening, symmetrical
rotation should be applied to ensure uniform force in all
directions and avoid oil leakage. ;
5 Insert the sensor into the wrench to complete the sensor
installation.
6 Connect the power cable and communication cable separately
according to the definition;
7 Check that the line is normal, you can turn on the sensor power,
and the sensor can work normally.
4. Application
Used in fuel oil tank for truck
7. Product picture
******************************************************************************************************************************************
Please send us emali for more information, we will reply you in 12
hours.
We will provide 12 months of warranty, and lifetime maintenance for
products.
Fully tested before delivery.
We supply high quality fuel level sensor, and provide high level
services.
We believe once cooperation can keep you as our friend. We look
forward your inquiries.
Company Profile
Xi'an Kacise Optronics Co.,Ltd. is a professional manufacturer of
measuring instruments , located in China xi’an City. Since 2008,
Xi'an Kacise focused on the development and production of pressure,
level and flow measuring instruments .
We have been specializing in manufacturing pressure, level and flow measuring instruments and related products for 10 years. Based on experienced technical
and management personnel, through efforts of our entire staff, we
have become a professional measuring instrument manufacturer and
solution provider. And we are continuously trying to improve
product quality.
Xi'an Kacise is qualified with ISO 9001-2008, GJB 9001B-2009, CE,
intrinsic safety explosion-proof and isolated safety
explosion-proof certificates, etc. which ensure that our products
comply with international standards.
Kacise sensors have already been exported to America, Spain,
Australia, Chile and 20 other countries and regions, and received
many favorable feedbacks. Our overseas distributers are also
increasing. We regard “reasonable prices, efficient production time
and good after-sales service” as our tenet, and hope to cooperate
with more customers for mutual development.
Our goal is simple: to sell the best products at the best prices,
and provides industry-leading customer service. We personally get
to know each of our customers, and we know how to discover the most
valuable part of our business , to help others achieve their goals.