Product Details
15L 300W Industrial Ultrasonic Cleaning Machine For Bicycle Chain
Cleaning
What Whale Cleen sonic Industrial Ultrasonic Cleaning Machine Can Do For You?
Ultrasonic cleaners do a phenomenal job of cleaning chains for
waxing. They use ultra high frequency sound waves to blast away
contaminants on chain parts. Importantly, ultrasonic cleaners
meticulously clean hidden, interior parts like pins, inner links
and inside roller surfaces where the majority of friction occurs.
The cleaning action, known as cavitation, is completely safe for
chains and other bike parts.
Because ultrasonic cleaners are powered by electricity, we can't
recommend using flammable solvents in them like mineral spirits and
denatured alcohol. Instead, choose water based (aqueous) cleaning
solutions that are non flammable. When combined with heat these
solutions clean extremely well with one exception: they aren't 100%
effective in removing new, unoxidized grease from a new chain. If
an aqueous solution is used in this situation a light film of
grease will remain on the chain.
To completely strip new grease and oil from a brand new chain we
recommend using our container method with mineral spirits and
denatured alcohol; from that point on the ultrasonic cleaner and
aqueous cleaning solutions can't be beat. Note: if you live in an
area that has banned mineral spirits, visit your LBS for a good
quality citrus degreaser to use in the first step of our container
method. No other type of solvent is advised for completely
stripping new factory chain grease off a chain.
In sum, a new chain out of the box should be cleaned with our
container method and petroleum solvents before its first waxing;
for all subsequent cleanings, use the ultrasonic cleaner with an
aqueous based solution for an incredibly clean and fast chain.
Specification:
Model | LanJ-J06 |
Capacity | 15L |
Tank size | 330*300*150MM |
Unit size | 360*325*285MM |
Ultrasonic power | 0~300W adjustable |
Heating power | 450W |
Customer's Feedback:
Cleaning Steps Of Ultrasonic Cleaning:
- Mix aqueous solution concentrate with hot tap water according to
manufacturer's recommendations (mix in measuring cup then pour into
UC, liquid should be minimum of 2/3 tank height). Time saving tip:
preheat 32 oz. of water in microwave before mixing. Big time saving
tip: use Swisher Tool to swish chain in boiling water to remove wax
and grit before ultrasonic cleaning. This pre-cleaning will reduce
the number of ultrasonic baths necessary for a clean chain.
- Put lid on UC and plug in, set temperature to 57C (135F) and timer
to 6 minutes (to degas aqueous solution). Degassing improves
cleaning performance.
- After degassing is finished, place chain in basket and basket in
UC, replace lid
- When temperature reaches 57C, set timer to clean chain for 6
minutes, then flip chain for additional 6 minutes (caution: chain,
solution and tank are hot!). Note: if chain was swished in boiling
water in step one to remove wax, bath temperature can be much lower
than 57C.
- Unplug UC, remove basket and place chain in large measuring cup
- With chain in cup, fill cup with hot tap water in sink, keep water
flowing into cup while agitating chain aggressively, empty and fill
cup several times to flush out solution and contaminants in chain,
minimum of 30 seconds intense rinsing/agitating is recommended
- Dry chain with clean rag, note any residue marks left on rag
(distinguish between dirt and simply wet marks left by chain)
- Coffee break: it is possible to stop now if no dirt was left on rag
- see additional notes at bottom of page for clarification - but
for cleanest and fastest chain continue remaining steps to assure
chain is as clean as possible before waxing.
- Pour out dirty cleaning solution from tank, clean tank with paper
towels, including wax clinging to sides of tank (reminder: tank is
hot!)
- Mix new solution with hot tap water as in step #1 above, pour into
tank, put lid on, plug in UC
- Set temperature to 57C and timer to 6 minutes to degas
- After degassing is complete, place chain in basket and basket in
UC, replace lid
- When temperature reaches 57C, set timer to clean chain for 6
minutes, then flip chain for additional 6 minutes
- Unplug UC, remove basket, place chain in cup for second rinsing as
step #6 above
- After thorough water rinse, blow chain dry with compressed air if
possible, then dry with clean rag (if any marks appear on rag,
repeat process with fresh concentrate and water). Note: when in
doubt, replace solution and clean more!
- Final step: place chain in clean, clear plastic container (Target
"Monster Mix" container preferred) that has lid, add denatured
alcohol to cover depth of chain, put lid on, swish for 45 seconds,
remove chain and dry with clean rag, hang chain 15 minutes before
waxing. Note: check container for debris on bottom (likely), repeat
alcohol rinse with new alcohol (clean container with paper towels
before refilling). For fastest chain plan on multiple alcohol
baths.
Company Profile
We, Guangdong Blue Whale Utrasonic Cleaning Equipment Co., Limited
is located in both Dong Guan City and Shen Zhen City, Guang Dong
Province. With the trust and support of our customers, we have more
than 18 years experience in this filed, Then we want to do some
difference from the market, not only selling but also helping.
For distributors, we provide superb equipements and good
solutions(include 12 cleaning serise) for your customer, free
training and free aftersales to make long term and win-win result.
For terminal clients, we support u best quality machine and good
service and cleaning solution till u make full use of the
equipments.
We have strong customer feedback in many industries like
Automotive, Molds, Aerospace, Firearms and etc.
We are here for you at 24/7. Please do not hesitate to contact us
if you are interested in our products.