Power 1000w Safety Test Equipment Mobile Phone Directional Drop Test Machine

Power 1000w Safety Test Equipment Mobile Phone Directional Drop Test Machine

Mobile phone directional drop test machineJD-6001C

Safe use instructions

Read the instructions carefully before using the device to avoid loss due to improper operation.

This equipment should be handled with care when shipping to your company, with a more spacious space. Perform a check before use, and the silk and fastening parts are loose during transportation.

This equipment should be sent to professional operators during the operation, and non-professional operators should keep a certain distance from the equipment.

The power supply used by the device is AC220V. The ground wire must be grounded. The voltage inside the chassis is 220V. Do not open the rear door of the chassis at will. The machine should be cleaned once every month of use and lubricated at the lubrication point. Perform another check after one year from the date of purchase, due to the consequences of not operating safely. The company is not responsible.

1. Introduction

1.1

Mobile phone directional drop test machine This machine is designed to evaluate the impact of the product on the performance of the product when the product is actually used. It is suitable for: small mobile phones, PDAs, telephones, electronic dictionaries, CDs, MP3s, adapters, etc. Electronic products for original attitude and acceleration drop test

Manually put the product into the fixture to clamp → the clamp rises to the set height value to stop → press the drop button (release button icon on the touch screen) → the clamp and the product together fall freely → when falling to 300mm (can be adjusted according to product adjustment The range refers to the height of the edge, the angle, the face and the contact surface, which can adjust the height of the sensor switch. The clamp releases the product → the product falls freely on the test board.

In order to ensure that the system operates as expected, the following must be done

1. The operator has the qualification for equipment operation

2. Operators have safety knowledge training

3. Read and follow the relevant instructions of the operating instructions

4. Operate according to the technical data of this manual

5. Enter the maintenance and maintenance of the equipment on time.

1.2 Training

This manual is intended for the relevant technical personnel, that is, those who have passed the level of training for the test equipment authorized and conducted by our company. Only formal training personnel can work correctly in accordance with the relevant instructions in this instruction manual. It is strictly forbidden to operate this equipment without unauthorized personnel of such training personnel. We are not responsible for the losses caused by the use of non-standards.

1.3 data

Size and weight

Electrical information

Environmental conditions

2. Safety

Remarks: Please read this chapter before operating the equipment and doing any work related to it! This chapter contains information that is important to protect your personal safety. Staff at any point during the warranty period of the equipment must carefully read and understand the contents of this chapter.

2.1 Security Identification

2.2 Security Responsibility:

The following is the distribution of the use of equipment safety responsibility

1. Our company is responsible for the safety of the equipment

2. The user is responsible for the security of the device

3. Users should ensure that all safety-related work areas and equipment are labeled with safety rules

3. Precautions

1. The 220V voltage in the control box of the machine, non-professionals are strictly prohibited to open the door and remove components.

2. This machine is an object test. It is strictly forbidden to reach into the frame.

3. The machine should be placed on a level surface to keep the machine dry and clean.

4. After the test is completed, the machine should be lowered and the power cord should be unplugged.

5. Do not unplug the power supply while working.

4. Maintenance and warranty

1. This instrument is a precision test equipment, and the user should be a person.

Maintenance, do not disassemble at will to avoid human damage

2, under the normal use of the machine, the company's warranty one

Year-end maintenance

If the equipment is insufficient, please give us your valuable comments.

5. Technical specifications

1, test height: 300~1700mm (can be set)

2, machine power supply: AC220V, 50Hz, 3A

3, drop height setting: scale and set height mm

4, Panasonic servo motor: AC Panasonic servo motor 400W,

5, transmission mode: the use of imported 5mm high-precision timing belt and synchronous wheel

6, the minimum separation height: 300mm

7, the use of gas source: ≥ 0.5MPa

8, machine reference size: W11000xD1100xH2050mm

9, machine reference weight: 150kg

10, the maximum size of the clamping product: W240xD170xH30mm (small products are available)

11, the maximum weight of the clamping product: 1.5KG

6. Device structure description

Equipment structure as shown

7. Operating instructions

1. Turn on the power to enter

2. Press to enter the system (automatic operation screen)

Automatic operation screen

Testing speed: refers to the rising and falling speed of equipment - - - mm / s (large and fast numerical value, small and slow numerical value)

Suspension height: refers to the height used to clamp the product. After the equipment automatically reduces and resets, it automatically rises to the set suspension height - - - mm.

Set height: Set the final height of rise - - - mm, stop running at high arrival.

Current height: refers to the current operating height - - - mm

Final velocity: The time from the beginning of the release to the grating induction to the sample. In the program, the velocity = 9.8 m/s* time is used to convert the instantaneous velocity - - - m/s.

Counting Settings: Set the total number of runs - 1-999999 settings

Current Number: Refers to the current number of runs displayed, the number of arrivals should be cleared at startup.

Number clearing: refers to the current number of runs in the state of zero clearing

System reset: refers to the system reset when the key failure and system reset failure occur in operation.

Automation: Press the auto-run button first when selecting, and select the right one when the next indicator light is on.

Start-up: refers to the start-up operation of the equipment when the automatic operation is selected (set the working parameters correctly before start-up). The lowest start-up point of the equipment reaches the suspension height, the sample is clamped, and the start-up operation stops at the set height.

Clamping: refers to the product edge, corner, side test clamping switch

Release: When the equipment has stopped running at a set height. Sample and fixture are released at the same time by pressing release button for drop test

Manual operation: refers to entering the manual operation screen

System parameters: refers to entering the system parameters setting screen

Manual operation

Manual: By pressing a manual button, you can manually return to the origin, clamp, release, rise and fall.

Back to the origin: refers to equipment running to the lowest point

Clamping: refers to manual clamping: refers to the product edge, corner, side test clamping switch

Release: refers to the manual equipment running to a set height after the stop. Sample and fixture are released at the same time by pressing release button for drop test

Rise: Hand-operated equipment rises, let go and stop immediately

Drop: Hand-operated equipment drops, let go and stop immediately

System recovery: refers to the operation of the key failure and system reset failure can be reset according to the system.

User Number and User Password: refers to the entry system parameters screen (2) (222888)

Automatic operation: referring back to the automatic operation screen

System parameters: Fill in the correct user number and password, and you can enter the system parameters screen.

system parameter

Start-up delay: refers to the automatic return delay of S, before the start-up rise (waiting time)

Origin frequency: refers to the speed of equipment running to the lowest point s (large and fast numerical value, small and slow numerical value)

Frequency ratio: refers to the rising and falling frequencies (can not be modified)

Gear ratio: refers to the motor deceleration ratio (can not be modified)

Acceleration and deceleration: refers to the rate of rise and fall (can not be modified)

Drive subdivision: refers to motor driver subdivision (not modifiable)

Synchronization wheel diameter: refers to the same synchronization wheel diameter value (can not be modified)

Compensation height: refers to the actual height of the product's falling contact surface (such as marble surface) and the product's falling surface, which can be modified - - - mm

Automatic operation: refers to returning to the automatic operation screen

Manual operation: pointing back to manual operation screen

Equipment operation process

Press (manual operation) to enter the manual operation screen - - press (back to the origin) to reset the device at the lowest point.

Press (automatic operation) to return to the automatic operation screen

3. Setting (Test Speed) - - mm/s (Large and Fast Number, Small and Slow Number)

4. Setting (pause height) refers to the height used to clamp the product. The equipment automatically falls down and resets and rises to the set pause height - - - mm.

5. Setting (Setting Height) means setting the final height of rise to set the final height - - - mm, and stopping operation at the high degree of arrival.

6. Select the right indicator when it is turned on by pressing (automatic) next to it.

7. Press (start) the device will rise to the set suspension height - mm stop.

8. The edge, corner and side of the test product will be put into the fixture, and the gripper will be carefully clamped.

9. Clamp the product according to (clamp)

10. Press (start) device will rise to set height - mm stop

11. When the sample and fixture are released at the same time and fall to a height of 300 mm from the falling surface, the fixture automatically opens the product and falls freely through optical fiber infrared induction. The release time is the time from the beginning to the grating induction to the sample. The instrument automatically calculates the instantaneous velocity - - - m/s.

12. In order to accelerate the automatic drop of the falling frequency equipment, it rises again to reach the set suspension height - mm stop.

After the test, check the damage of the specimen. The drop test is carried out according to the product requirements.

8. Main standard parts details

9. Accessories

10. Factory inspection report

Factory date: December 7, 2016

11. Service order

Note: The following conditions are not covered by the warranty:

1. Equipment damage caused by not using the specified range.

2, due to natural disasters (such as: floods, fires, lightning, etc.)

3. After the warranty period has expired, the company only undertakes maintenance services for the equipment and appropriately charges a certain fee.

4. During the warranty period, if you do not allow the company to dismantle it, you will be responsible for it.

Dongguan Jiedong Test Equipment Co., Ltd.

Business overview:

Dongguan Jiedong Test Equipment Co., Ltd. is located in Tangxia Town, Dongguan City. After years of hard work, Jiedong has established a production base in Dongguan, research and development, sheet metal, production, sales, after-sales, leasing, testing, and governance. With one-stop services such as import and export. The company has always focused on the technology and laboratory solutions of the most reliable reliability environmental testing equipment, and has become the national high-tech enterprise, the executive director unit of China Aerospace Systems Science and Engineering Research Institute, and the governing unit of Dongguan Metrology Association. lSO14001: 2015 environment, lSO9001: 2015 quality system certification. The products are constantly improving, and the customers are in the scientific and technological fields of scientific research, military industry, national defense, colleges, quality inspection, automobile, new energy, battery, optoelectronics, artificial intelligence, precision electronics, power tools, medical, communication, etc. After-sales service, each link takes the customer's point of view and needs as the starting point for thinking, and adheres to the line of excellence and continuous improvement.

Management mechanism:

Jiedong passed and strictly implemented the ISO9001:2008 quality management system, ISO14001-2004 environmental system certification, European CE product certification, OHSAS18001 occupational health and safety management system certification. Carefully implement GB, GJB, IEC, MIL, JB, ZBY and other product standards; Jiedong strictly follows the 7S management method and ERP mechanism, and explores the unique and effective specialization for the environmental test equipment industry's many years of characteristics and experience. The management methods of research, production, sales and service can provide customers with all kinds of ring test products and services with high quality, high efficiency and precision.

Main products:

※ Environmental simulation test equipment: constant temperature and humidity chamber, high and low temperature test chamber, thermal

shock test chamber, salt spray test chamber, xenon lamp aging test chamber, rain test Inspection box, ultraviolet aging test chamber, dust

test chamber, rain test chamber, high temperature precision oven, simulated transport vibration table, etc.;

※ Battery safety performance testing equipment: battery extrusion testing machine, battery needle testing machine, battery explosion-proof test

box, battery burning test box, high-altitude low-pressure mode Preliminary test chamber (low pressure test chamber), drop test machine,

heavy impact test machine, thermal shock test chamber (heat abuse test chamber), battery needle punching and extrusion Machine, battery

short-circuit test machine, battery washing test machine, seawater immersion test machine, battery pack reverse test machine, battery safety

performance comprehensive test laboratory, etc.;

※ Material mechanics testing equipment: electronic tensile testing machine, computerized tensile testing machine, universal testing machine,

high and low temperature tensile testing machine, four-point compression testing machine,Table type tensile testing machine, horizontal

tensile testing machine, etc.;

※ Mobile phone and notebook testing equipment: Click the line test machine, compression test machine, compression life test machine, twist

test machine, drop test machine, shaft life Life test machine, etc.

※ Wire testing equipment: wire bending (swinging, bending) testing machine, FPC folding test machine, wire bending resistance testing

machine, taper rocking test machine, line Material elongation (elongation) test machine, etc.;

※ Key detection equipment: button life test machine, switch rotation life test machine, button fatigue life test machine, fully automatic button,

switch load strokeLine testing machine, etc.

※ Terminal insertion and removal testing equipment: plug-in life testing machine, insertion force testing machine, fully automatic insertion force

testing machine, etc.;

※ Abrasion test equipment: anti-friction test machine, ink decolorization test machine, alcohol rubber wear test machine, etc.;

※ Leather and rubber testing equipment: TABER wear tester, Martindale wear tester, low temperature cold resistance tester, leather

endurance tester, color fastnessTesting machine, linear abrasion testing machine, rubber oil resistance testing machine, etc.;

※ Combustion test equipment: vertical horizontal burning test machine, needle flame burning test machine, glow wire test machine, automobile

interior material burning test machine, large-scale combustion Cabinet, leakage tracking test machine, etc.;

※ Other testing equipment: lithium battery moisture measuring instrument, falling ball impact testing machine, shotgun impact testing machine,

etc.;

Application areas:

Dongguan Jiedong Test Equipment Co., Ltd. has excellent research and development products, advanced equipment and complete testing means. The company has first-class technical talents and management talents, which makes the company's products always in a good position in the same industry. Dongguan Headquarters Factory is located in Dongguan City, which is known as the world factory with convenient transportation and developed manufacturing industry. Our products are widely used in scientific research, military, electronics, electrician, LED, automotive, plastic, hardware, toys, paper products, chemicals, household goods and other industries, and are applicable to various research units, quality inspection organizations, academic discussions and other fields. To provide customers with a variety of testing and testing equipment in line with national standards and related industry standards, international standards (GB, GJB, IEC, MIL, DIN), to achieve international quality, localized prices.

Phone: 86-0769-26265799

Address: No. 17, Sanheng Road, Lianhu South, Tangxia Town, Dongguan City, China