China Categories
English
Home /Refrigeration & Heat Exchange /

CNS11888 100mm Rolling Ball Tack Tester For Adhesive Tape

CNS11888 100mm Rolling Ball Tack Tester For Adhesive Tape

Brand Name:POOTAB
Certification:ISO,CE,SGS
Model Number:PT-6030
Minimum Order Quantity:1 set
Delivery Time:3 working days after confirm order
Payment Terms:T/T, L/C, Western Union
Contact Now

Add to Cart

Verified Supplier
Location: Dongguan Guangdong China
Address: 150 Fenxi Road, Shangjia Urban Industrial Park, Building 2, Wanjiang District, Dongguan City, Guangdong Province
Supplier`s last login times: within 29 hours
Shipping
lt's easy to get a shipping quote! Just click the button below and complete the short form.
Get Shipping Quote
Product Details Company Profile
Product Details

Initial Tack Tester Rolling Ball CNS11888 Adhesion Test


Definition of primary tack :
Initial Tack: the adhesion of the adhesive tape to an object when the adhesive surface is temporarily contacted with minute pressure between the object and the pressure-sensitive adhesive tape.


Introduction: PT-6030 tape initial tack tester is an instrument for testing the initial tack of pressure-sensitive adhesive tapes and products similar to pressure-sensitive adhesive tapes. Its various technical indicators are in line with the provisions of GB/T 4852-1984. Its principle is to roll a rolling ball over the sticky surface of the adhesive tape lying flat on an inclined plate, and evaluate its initial tack according to the maximum number (size) of the sticky surface that can be stuck by a specified length of the sticky surface.


Equipment spec.:

  • Design Standard:GB/4852,CNS11888
  • Tilt angle: 20° ~ 40° adjustable, ( normal use 30°)
  • Rolling ball: Stainless Steel , 29 pieces,not including No.1, No.27, No.31
  • Weight: 500g
  • Run-up segment: 100mm

Rolling Balls spec.: (Noted:According to(GB/T4852-2002), a set balls including 29 pieces,exclude 1/32,27/32,31/32)

NoDia(mm)NoDia(mm)NoDia(mm)NoDia(mm)
10.79497.1441713.4942519.844
21.558107.9381814.2882620.638
32.381118.7311915.0812721.431
43.175129.5252015.8752822.225
53.9691310.3192116.6692923.019
64.7621411.1122217.4623023.812
75.5561511.9062318.2563124.606
86.3501612.702419.0503225.4

Operation Steps Of Roll Ball Tack Testing :

1. Place the machine on a stable table so that the pointer is aligned with the zero line of the Angle plate; Adjust the floor to level the work surface.

2. Then adjust the work surface to the Angle required by the test, generally 30°.

3. Fix the adhesive tape (test strip) to be tested on the working table (100 mm below the center of the ball is the running section), and fix the bottom edge of the test strip extending to the steel ball box with 500g weight, so that the test strip is naturally flat under a heavy weight.

S1. The test slice should be at least 4 pieces with a width (10 ~ 80 mm) and a length of about 250mm. If the elongation of the test slice is large, the test slice should be left for a period of time before the test.

S2. For the run-up section, the transparent polyester film of electrical appliances with a thickness of 25 m and a length of more than 100 mm is pasted on the adhesive surface of > at the designated position of the test piece, with a length of 100 mm.

S3.100mm run-up is adjusted by adjusting the bolts on the machine and corresponding positions of the rolling balls with different ball sizes.

4. Pre-select maximum roll

Adjust the starting position of the ball, select balls with different ball Numbers, and repeat the systematic operation of ball cleaning and rolling.Pick the largest of the primary balls that are stopped in the measurement interval (the ball does not move for more than 5 seconds).Take the largest ball selected from the same test piece and the two balls with the ball number and its adjacent size, and test them on the same sample once each to confirm the ball with the largest ball number.(rolling the test on the same chip several times before picking the largest ball is acceptable, but it cannot be used as official test data.)

5. Formal testing

Take three samples and roll the ball on each of them with the maximum ball number selected.If a sample cannot stick the ball, the smaller ball can be used for a test. If it still cannot stick, the test shall be retested according to the steps of "pre-selected maximum ball" and "formal test".

6. Test results

The test results are expressed as the median ball number (ball diameter) of the ball test results of the three samples in the formal test.


Rollong Ball Tack Tester Photo :


China CNS11888 100mm Rolling Ball Tack Tester For Adhesive Tape supplier

CNS11888 100mm Rolling Ball Tack Tester For Adhesive Tape

Inquiry Cart 0