2L Fast Removing Contaminant Digital Ultrasonic Cleaner For Nail Salon

2L Fast Removing Contaminant Digital Ultrasonic Cleaner For Nail Salon​

Regulations covering cleaning implements used in nail spas can often be met by first immersing manicure tools and pedicure tools in an ultrasonic cleaner to remove gross contaminants that may be picked up during clipping and filing then adhere to tool surfaces. These contaminants can cause mycobacterium and staph infections as well as fungal infections. Following ultrasonic cleaning tools are disinfected or sterilized before being stored for future use.

Effectiveness of Nail Salon digital Ultrasonic cleaner over other methods of cleaning

2. How Nail Salon digital Ultrasonic Cleaner work

The first step is to fill the ultrasonic cleaner tank with a safe, biodegradable ultrasonic cleaning bath, which can be formulated by adding a 1-ounce tube of CLN-LR012 per gallon of water. After rinsing the tools with water, they are placed into the unit’s mesh basket. The unit is turned on, degassed by operating for about 30 minutes (or 10 minutes if the unit has a Degas mode), and the basket is lowered into the bath for the actual ultrasonic cleaning process.

Rapid, thorough, quiet cleaning is accomplished by ultrasonic energy. This is produced by the unit’s ultrasonic generator and transmitted into the ultrasonic cleaning bath by transducers mounted on the bottom of the tank. The process creates billions of microscopic bubbles that implode with great force when they come into contact with the implements being cleaned. The action is called cavitation. It blasts dirt and contaminants away without damaging the implements. Bubbles penetrate the tiniest cracks and crevices that are virtually impossible to clean by manual soaking and scrubbing. After being cleaned the implements are rinsed, sanitized and stored.

The intuitive control panel on the ultrasonic unit allows operators to set ultrasonic cleaning time and bath temperature in accordance with the load being cleaned. SKymen units have knobs that are turned to the appropriate time and temperature settings. Despite their simple appearance, these units are fully microprocessor controlled. Other manufacturers offer analog and/or digital controls and displays.

3.Features of digital ultrasonic cleaner JP-010T

(1)Degas function enhances cleaning effect and reduce oxidation on your Nail instrument.

(2)Strong power for cleaning Nail instrument.

(3)5 times digital time setting to meet your different cleaning requirement.

(5)Suitable frequency for nail instrument.

4.Why nail salon digital ultrasonic cleaner is an important first step

Based on accepted procedures used to clean dental and surgical instruments many states are now requiring nail spas to include ultrasonic cleaning as the first step in cleaning, then sanitizing or sterilizing their manicure and pedicure tools. That’s because the sonication that occurs in these cleaners safely and quickly removes adhering particles not easily dislodged by manual scrubbing. Manually cleaning these tools, by the way, risks chance of injury from points and sharp edges.

5.How to clean Nail tool with Skymen nail salon digital ultrasonic cleaner?

Skymen ultrasonic cleaners are compact, efficient and quickly accomplish pre-sterilizing nail spa implements. An example for a small-to-medium sized nail salon is the 2.5L capacity.JP-2500 equipped with a lid, heater, timer and basket. These cleaners are available in several sizes to accommodate larger manicure and pedicure salons.

A recommended cleaning solution concentrate is enzymatic MedClean C7 formulated for medical and surgical instruments and available in gallon containers. This dilutes to 1 to 3 ounces per gallon of water making it not only effective but also an economical choice. Recommended solution temperature is approximately 50C. Here’s a suggested setup and operating procedure:

1. 1. Place your ultrasonic cleaner in proximity to an electrical outlet. Add water to the fill line and the correct amount of MedClean C7 based on the capacity of the tank.
2. 2. Turn on the ultrasonic unit for about 10 minutes to both mix the solution and drive off entrained air. This step must be taken each time you prepare a new solution. When you are ready to clean set the thermostat to 60?C.
3. 3. Arrange the implements in the basket and avoid, if possible, their contacting each other.
4. 4. Lower the basket into the solution making certain all surfaces are fully immersed. Set the timer for 10 minutes and activate the ultrasound.

Sonic cleaning involves the implosion of millions of microscopic bubbles on the surface of the instruments to blast away contaminants. At the end of the cycle remove the instruments. After rinsing they are ready for disinfecting or sterilizing.

Cleaning solutions should be replaced on a regular basis according to applicable regulations for nail salons. Rinse the tank with fresh water before preparing a new bath.

Call the iUltrasonic cleaning experts at 973-440-2191 for answers to your questions on equipment and procedures for cleaning manicure tools and pedicure tools.

6.Specification of digital ultrasonic cleaner

7.Detailed picture of digital ultrasonic cleaner

8.Other recommendation:

If this tank size is not suitable for your dental tool cleaning, we have other smaller or bigger machine for you to choose.Please check other model on our website:www.skymen.cc

9. Skymen Policy For Distributor

We are only specializing in designing and producing ultrasonic cleaner so we need our partners in medical industry,always!

We will keep our quality and competitive price for our distributor.

If you would like to cooperate with us, please contact me directly.

10. Skymen Advantage

We have been in this industry for 10 years and we are supplying machines to all seller all over the world.All distributor is welcome for win-win coperation.

We have passes ISO,High Tech Company,CE,RoHS,FCC, National Medical Instrument Approval.

ISO:

CE:

Skymen Technology Corporation Limited, which is a leading manufacturer and national high-tech enterprise, was founded in 2007. There are 2 factories of Skymen, one is located in Shenzhen, closed to HongKong. And the other is located in Shaoguan, Guangdong province, China.

We have been focusing on R&D of ultrasonic equipment & cleaning solution for more than 17 years with over 300 employee and plant size 35,000 square meter. Products include CE, FCC, PSE, KC and other safety certification, as well as ROHS,PAHS, REACH, SCCP environmental certification, and passed the factory audit BSCI, ISO9001 quality management system.

There are more than 120 patents & certificates in total. Our products range covers industrial ultrasonic cleaner, homeuse ultrasonic cleaner, commercial ultrasonic cleaner, full-automatic ultrasonic cleaning machine, ultrasonic transducer rod series, ultrasonic transducer plate series, tunnel cleaning machine, large hydrocarbon ultrasonic cleaning equipment with PLC, large ultrasonic cleaning equipment with vacuum implementation, etc.

2023 Skymen self-built Shaoguan industrial Park

2020 New Factory Industrial Park

Shenzhen R&D Basement

Shenzhen Marketing Center

Skymen Company Introduction