1 - 10 Results for signal converter and isolator from 8541 Products
24V DC 2000mW Digital Signal Isolator 8ch RS485 Signal Converter
24V DC 2000mW Digital Signal Isolator 8ch RS485 Signal Converter Signal Converter 8ch Analog Signal Convert to RS485 Analog Data Acuisition Module 1. General Introduction The LS-TD4018 is an industrial grade analog acquisition product that supports measure range with -15mV ~+15mV, -50mV~50mV, -100mV~+100mV, -500mV~+500mV, -1V~+1V, -2V~2V, -20mA~20mA and J type, K, T, E, R, S, B, N type TC signal 8 channels input. It adopts standard MODBUS RTU...
24V DC Power Supply Analog Signal Converter RS485 RS232 interface
24V DC Power Supply Analog Signal Converter RS485 RS232 Interface LS-WJ31 Analog signal to RS232/RS485 Converter Features: Features: RS-485/232 interface, isolation convert standard analog signal output Analog signal output accuracy is better than 0.2% Can calibrate module output accuracy Signal output / communication interface isolation voltage 3000VDC Wide supply range: 8 ~ 32VDC High reliability, easy programming, easy to install and wiring...
LS-TD4015 6ch RTD signal Convert to RS485 PT100 to RS485 Temperature Transmitter Din Rail Mounting
Signal Converter 6ch RTD signal Convert to RS485 PT100 to RS485 Temperature Transmitter General Introduction The LS-TD4015 is an industrial grade standard RTD acquisition product that supports PT100, PT1000, Cu50, Cu100, Ge53, BA1, BA2, R5000 and R500 6-channel three-wire RTD inputs. RS485 interface is optoelectronic isolated. AD acquisition part is also modulus optoelectronic isolated. It adopts standard MODBUS RTU protocol. Complaint with...
LS-WJ31 Analog Signal to Serial Signal Converter Analog 4-20mA to RS232, RS485 Converter
LS-WJ31 Analog signal to RS232/RS485 Converter Features: Features: RS-485/232 interface, isolation convert standard analog signal output Analog signal output accuracy is better than 0.2% Can calibrate module output accuracy Signal output / communication interface isolation voltage 3000VDC Wide supply range: 8 ~ 32VDC High reliability, easy programming, easy to install and wiring User-programmable settings module address, baud rate, etc. Set the...
4-20mA 0-20mA 24V DC 50mA Signal Converter Isolator
LS-THG-IP series analog input distribution isolator, is to provide isolation power for two-wire transmitters and three-wire transmitters on site, and also simultaneously transfer and output the 0/4~20mA signal produced by the transmitter. It needs independent 24V DC power supply. Its power supply, input and output are separated to each other. Input Input signal: 4-20mA; 0-20mA Distribution voltage: 24V, (maximum drive current 30mA) Input...
LS-WJ28 Rs232 Rs485 to 8AI 4-20mA or 0-5V Analog Signal Converter
This is a 24 Bits AD data acquisition converter. It has 8AI, can converter analog signal to serial RS232 or RS485 Application area Industry automation area signal measurement, monitoring and control RS-485 remote I / O, data acquisition application of intelligent building control, security engineering industrial automation control system Features: 8 AI, isolated converter RS-485/232 output 24-bit AD converter, accuracy>0.05% 4-20mA/0-20mA current...
LS-THG-IP Series Current Input Signal Converter Din Rail Mounting DC24V Power Supply
Input Input signal: 4-20mA; 0-20mA Distribution voltage: 24V, (maximum drive current 30mA) Input impedance: ≤50Ω Output Output signal: 4-20mA; 0-20mA; 0-5V; 0-10V Output load resistance: RL ≤ 500Ω (when the output is a current signal); RL ≥ 10KΩ (when the output is a voltage signal) Basic parameters Power supply: DC24V, ±10% Current consumption: ≤50mA (one input and one output, 24V power supply, power distribution input, 20mA output); ≤70mA (one...
Response Time 10ms 30mA 24V DC Current Signal Converter
Input Input signal: 4-20mA; 0-20mA; 0-75mV, 0-5V; 0-10V Distribution voltage: 24V, (maximum drive current 30mA) Input impedance: current input: ≤50Ω; voltage input: ≥300KΩ Output Output signal: 4- 20mA; 0-20mA; 0-5V; 0-10V Output load resistance: RL≤500Ω (when the output is a current signal); RL≥10KΩ (when the output is a voltage signal) Basic parameters Power: DC24V, soil 10% or AC85-265V Consumption current: ≤50mA (one input and one output, 24V...
NPN to PNP pulse signal isolated transmitter blue DIN35 signal converter 3000V isolation 3 in 3 out
three input three output Keywords: Encoder | differential signal | pulse | isolated converter | Signal Conditioner Features: >> Differential signal/pulse signal isolated transmitters >> Support A, B, and Z three-phase differential simultaneous conversion >> 3 inputs, 3 outputs, selectable output pulse amplitude >> No change the original waveform frequency, response speed is over 500KHz >> Three-isolation:signal input/Power/signal output 3000VDC >...
NPN to PNP pulse signal isolated transmitter blue DIN35 signal converter 3000V isolation 3 in 3 out
three input three output Keywords: Encoder | differential signal | pulse | isolated converter | Signal Conditioner Features: >> Differential signal/pulse signal isolated transmitters >> Support A, B, and Z three-phase differential simultaneous conversion >> 3 inputs, 3 outputs, selectable output pulse amplitude >> No change the original waveform frequency, response speed is over 500KHz >> Three-isolation:signal input/Power/signal output 3000VDC >...